## What is Pressure

**Pressure** is a measure of the **force exerted** per unit area on the boundaries of a substance. The standard unit for **pressure** in the SI system is the **Newton per square meter or pascal (Pa)**. Mathematically:

**p = F/A**

where

**p is the pressure****F is the normal force****A is the area of the boundary**

Pascal is defined as force of 1N that is exerted on unit area.

**1 Pascal = 1 N/m**^{2}

**kPa**, the

**bar**, and the

**MPa**.

**1 MPa 10**^{6}N/m^{2}**1 bar 10**^{5}N/m^{2}**1 kPa 10**^{3}N/m^{2}

In general, pressure or the force exerted per unit area on the boundaries of a substance is caused by the **collisions** of the **molecules** of the substance with the boundaries of the system. As molecules hit the walls, they exert forces that try to push the walls outward. The forces resulting from all of these collisions cause the **pressure** exerted by a system on its surroundings. Pressure as an **intensive variable** is constant in a closed system. It really is only relevant in liquid or gaseous systems.

## Pounds per square inch – psi

The standard unit in the English system is the **pound-force per square inch (psi)**. It is the pressure resulting from a force of one pound-force applied to an area of one square inch.

**1 psi 1 lbf/in**^{2}= 4.45 N / (0.0254 m)^{2}≈ 6895 kg/m^{2}

Therefore, one pound per square inch is approximately 6895 Pa.

The unit of measurement called standard atmosphere (atm) is defined as:

**1 atm = 14.7 psi**

The standard atmosphere approximates to the average pressure at sea-level at the latitude 45° N. Note that, there is a difference between the **standard atmosphere** (atm) and the** technical atmosphere** (at).

A technical atmosphere is a non-SI unit of pressure equal to one kilogram-force per square centimeter.

**1 at = 14.2 psi**

See also: Pascal – Unit of Pressure

See also: Bar – Unit of Pressure

See also: Typical Pressures in Engineering

## Absolute vs. Gauge Pressure

Pressure as discussed above is called **absolute pressure**. Often it will be important to distinguish between **absolute pressure** and **gauge pressure**. In this article the term pressure refers to absolute pressure unless explicitly stated otherwise. But in engineering we often deal with pressures, that are **measured** by some devices. Although absolute pressures must be used in thermodynamic relations, **pressure-measuring** devices often indicate the **difference** between the absolute pressure in a system and the absolute pressure of the atmosphere existing outside the measuring device. They measure the **gauge pressure**.

**Absolute Pressure.**When pressure is measured relative to a perfect vacuum, it is called absolute pressure (psia). Pounds per square inch absolute (psia) is used to make it clear that the pressure is relative to a vacuum rather than the ambient atmospheric pressure. Since atmospheric pressure at sea level is around 101.3 kPa (14.7 psi), this will be added to any pressure reading made in air at sea level.**Gauge Pressure.**When pressure is measured relative to atmospheric pressure (14.7 psi), it is called gauge pressure (psig). The term gauge pressure is applied when the pressure in the system is greater than the local atmospheric pressure, p_{atm}. The latter pressure scale was developed because almost all pressure gauges register zero when open to the atmosphere. Gauge pressures are positive if they are above atmospheric pressure and negative if they are below atmospheric pressure.

*p*_{gauge}* = p*_{absolute}* – p*_{absolute; atm}

**Atmospheric Pressure.**Atmospheric pressure is the pressure in the surrounding air at – or “close” to – the surface of the earth. The atmospheric pressure varies with temperature and altitude above sea level. The**Standard Atmospheric Pressure**approximates to the average pressure at sea-level at the latitude 45° N. The**Standard Atmospheric Pressure**is defined at sea-level at*273*^{o}*K (0*^{o}*C)*and is:*101325 Pa**1.01325 bar**14.696 psi**760 mmHg**760 torr*

**Negative Gauge Pressure – Vacuum Pressure.**When the local atmospheric pressure is greater than the pressure in the system, the term**vacuum pressure**is used. A perfect vacuum would correspond to absolute zero pressure. It is certainly possible to have a negative gauge pressure, but not possible to have a negative absolute pressure. For instance, an absolute pressure of 80 kPa may be described as a gauge pressure of −21 kPa (i.e., 21 kPa below an atmospheric pressure of 101 kPa).

*p*_{vacuum}* = p*_{absolute; atm}* – p*_{absolute}

For example, a car tire pumped up to 2.5 atm (36.75 psig) above local atmospheric pressure (let say 1 atm or 14.7 psia locally), will have an absolute pressure of 2.5 + 1 = 3.5 atm (36.75 + 14.7 = 51.45 psia or 36.75 psig).

On the other hand condensing steam turbines (at nuclear power plants) exhaust steam at a pressure well below atmospheric (e.g. at 0.08 bar or 8 kPa or 1.16 psia) and in a partially condensed state. In relative units it is a negative gauge pressure of about – 0.92 bar, – 92 kPa, or – 13.54 psig.

We hope, this article, **Pound per square inch – psi**, helps you. If so, **give us a like** in the sidebar. Main purpose of this website is to help the public to learn some interesting and important information about thermal engineering.